CO2 laboratory incubator ICO180

for scientific researchfor cell culturesfloor-standing

<b>Overview</b><br>Controlled environment for reproducible cell culture. CO2 incubation with precise humidity management, hygienic design and advanced connectivity for laboratory workflows.<br><br><b>Range of functions</b><br>Calibration: Three freely selectable setpoints: temperature, humidity and CO2.<br>Interfaces: USB-C, Ethernet LAN.<br>Timer modes: immediate start; SetpointWAIT (starts after all setpoints reached); Timer on Event (starts at defined time).<br>Language options: English (default), German, French, Spanish, Portuguese, Chinese, Arabic, Hindi, Polish, Czech, Hungarian, Russian, Italian, Serbian.<br>Appliance functions: date/time (time zones, summer/winter time), display brightness, DistanceView (1–4 parameters, adjustable activation), network settings (IP, subnet, DHCP), language and volume (buzzer/key tone), power-failure behaviour, timer functions.<br>Adjustable parameters: temperature, CO2, humidity (option K7 required), O2 (option T6 required).<br>Control unit: 6.86" IPS multi-touch display (480 × 1280 px) with graphical presentation of actual/setpoint values and parameter curves.<br><br><b>O2 (only with T6 option)</b><br>Control: Anaerobic O2 regulation via N2 inlet with zirconium oxide sensor, integrated monitoring and error display. Filtered N2 supply for safe processing.<br>Adjustment precision: 0.1%<br>Setting range: 1–20% O2.<br><br><b>Temperature</b><br>Heating system: large-area multi-zone all-round heating with additional door, seal and rear-wall heating.<br>Setpoint range: +20 to +50 °C.<br>Working range: from 5 °C above ambient up to +50 °C.<br>Sterilisation programme: 60 minutes at 180 °C (sensors can remain in place).<br>Resolution/accuracy: 0.1 °C; spatial variation at 37 °C: ±0.3 K; temporal fluctuation at 37 °C: ±0.1 K.<br><br><b>Humidity</b><br>Humidification: passive via integrated water tank with condensate return (magnetically guided sealing lip). Humidity limitation by Peltier element. Option K7: active closed-loop control with capacitive sensor, micro-dosing pump with hot-steam generation and diaphragm pump dehumidification.<br>Accuracy: 0.5% RH<br>Setting range: 40–98% RH and RH-Off.<br><br><b>CO2</b><br>Control: Dual-beam NDIR CO2 sensor with pressure-compensated measurement and integrated monitoring. Filtered CO2 supply for reliable operation.<br>Temporal fluctuation: ±0.2%<br>Setting range: 0–20% CO2.<br><br><b>Safety</b><br>Power-failure behaviour: manual mode and program mode handling with stored parameters and queries for continuation depending on outage duration.<br>Temperature monitoring: dual Pt1000 sensors (DIN Class A) for mutual monitoring and automatic takeover on fault.<br>Alarms: visual and acoustic.<br><br><b>Standard equipment</b><br>Standard option: door-open detection (V5).<br>Factory calibration certificates: I (standard): +37 °C, 5% CO2; II (K7): +37 °C, 5% CO2, 90% RH; III (T6): +37 °C, 5% CO2, 90% RH, 10% O2.<br>Accessories: CO2 connection set with hose and clamp; water tank (B38737) and connection hose; stored sterilisation programme (60 min at 180 °C).<br>Door: fully insulated stainless-steel door with 2‑point compression lock.<br>Inner door: glass inner door with 8 mm Ø opening for gas sampling.<br>Internals: 2 perforated stainless-steel shelves (more up to 6 possible).<br><br><b>Stainless steel interior</b><br>Interior dimensions (W × H × D): 600 × 590 × 500 mm.<br>Inner cover thickness: 37.5 mm.<br>Volume: 177 L.<br>Max number of internals: 6; max chamber load: 90 kg; max load per shelf: 15 kg.<br><br><b>Textured stainless steel casing</b><br>Exterior dimensions (W × H × D): 748 × 793 × 689 mm.<br>Installation: 4 adjustable feet.<br><br><b>Electrical data</b><br>230 V, 50/60 Hz — approx. 1500 W.<br>115 V, 50/60 Hz — approx. 1500 W.<br><br><b>Ambient conditions</b><br>Installation clearances: rear ≥15 cm; top ≥20 cm; sides ≥5 cm.<br>Ambient temperature: 10 °C to 35 °C.<br>Maximum installation altitude: 2000 m above sea level.<br>Overvoltage category: II; Pollution degree: 2.<br><br><b>Packing / shipping data</b><br>Transport: appliance must be transported upright.<br>Customs tariff number: 8419 8998.<br>Country of origin: Federal Republic of Germany.<br>WEEE Reg. No.: DE 66812464.<br>Packed dimensions (approx., W × H × D): 925 × 1072 × 854 mm.<br>Net weight: approx. 98 kg; gross weight (carton): approx. 116 kg.<br><br><b>Standard units and certifications</b><br>Devices are safety-approved and bear CE marking.<br><br><b>Technical specifications</b><br><ul><li>Model: ICO180</li><li>Brand: Memmert</li><li>Type: CO2 incubator (ICO series)</li><li>Chamber volume: 177 L</li><li>Interior dimensions (W × H × D): 600 × 590 × 500 mm</li><li>Exterior dimensions (W × H × D): 748 × 793 × 689 mm</li><li>Temperature setpoint range: +20 to +50 °C; working range: from 5 °C above ambient to +50 °C</li><li>Temperature accuracy/resolution: 0.1 °C; spatial variation at 37 °C: ±0.3 K; temporal fluctuation at 37 °C: ±0.1 K</li><li>CO2 range: 0–20%; temporal fluctuation: ±0.2%; control: dual‑beam NDIR</li><li>Humidity range: 40–98% RH (or RH‑Off); accuracy: 0.5% RH; active control option: K7</li><li>O2 control (option T6): 1–20%, precision 0.1%, zirconium oxide sensor</li><li>Control/display: 6.86" IPS touch display (480 × 1280 px)</li><li>Interfaces: USB‑C, Ethernet LAN</li><li>Power: 230 V / 115 V — approx. 1500 W</li><li>Max. chamber load: 90 kg; max. load per shelf: 15 kg; max. number of internals: 6</li><li>Sterilisation programme: 60 min at 180 °C (sensors in place)</li><li>Alarms: visual and acoustic; temperature monitoring: dual Pt1000 (DIN Class A)</li><li>Transport: upright only; origin: Federal Republic of Germany</li><li>Net weight (approx.): 98 kg; gross weight carton (approx.): 116 kg</li></ul>